Liya Tech Center Instrument 810 Operation Manual(For Toursor X5)

Liya Tech Center Instrument 810 Operation Manual

Standard 2022 Revised Edition

Fault Status Display Area E: When the symbol is flashing, briefly press the M/3 key to switch the display interface to the E interface. The corresponding number under this interface represents the specific fault content as follows:

E-001: Motor Hall Sensor Fault
E-002: Throttle Fault
E-003: Controller Fault
E-004: Brake Fault
E-005: Voltage Fault
E-006: Communication Fault (Instrument does not receive controller signal)
E-007: Communication Fault (Controller does not receive instrument signal)

Wiring Configuration:

  1. Red Wire (VCC+): Power supply positive input

  2. Black Wire (GND–): Power supply negative

  3. Blue Wire (S1): Dual-drive control line

  4. Green Wire (TX): Communication transmit

  5. Yellow Wire (RX): Communication receive

  6. White Wire (DS): Controller ignition lock line

Wiring Mode:

  1. Red Wire (D+): Positive input of power supply

  2. Black Wire (GND): Negative pole of power supply

  3. Blue Wire (DS): Controller switch lock

  4. Green Wire (Tx): Communication transmission

  5. Yellow Wire (RX): Communication reception

  6. White Wire (Hall Signal): Hall sensor signal

Special Notes:
This instrument supports Bluetooth, NFC(This icon represents the NFC function), and password startup. The backend parameter P95 offers three options:

  • 0: No password/NFC required for startup (press the power button directly).

  • 1: NFC card required for startup.

  • 2: Both password (default: 1234) and NFC card can be used for startup.

Operation Steps:

  1. P95 = 0: Briefly press the power button to start.

  2. P95 = 1: Briefly press the power button. An "N" icon will appear, indicating NFC card scanning is required. Swipe the NFC card over the designated area (marked "NFC").

  3. P95 = 2: Briefly press the power button. Enter the 4-digit password (default: 1234) within 5 seconds. The first digit requires a long press (≥1 second), subsequent digits require short presses. Alternatively, swipe an NFC card.

Bluetooth Connection:

  1. Download the App:

    • Android: Scan the  QR code via a browser.

    • iOS: Search "MyTrip" in the App Store.

  2. Pairing:

    • Open the app and click the Bluetooth icon.

      LIVIVE

    • Search for devices starting with "LIVIAE" and connect.

    • Log in (guest login allows basic functions; registration is required for parameter adjustments).

Prevent others from misoperating and causing vehicle abnormalities.


How to register:

  1. Click to register an account and enter information according to the interface.
  2.  After the information is registered, you will jump to the login interface and click to log in.
  3. The Bluetooth search interface will appear. Click the name starting with LIVIAE , and a barcode scan box will appear. At this time, just scan the barcode or enter the barcode number and letter to bind to the vehicle interface. The barcode is usually in the manual or on the side or back of the instrument.

NFC Card Details:

  • Blue Master Card: Used for configuring new NFC cards. Store it securely (not for daily startup).

  • White Sub-Cards: Used for daily startup. If lost, use the master card to configure replacements.

How to use the blue master card:

  1. Set P96 to 1 or 2.

  2. Briefly press the power button (within 5 seconds) and swipe the blue master card over the NFC area.

  3. The number 1 will appear on the meter. When it appears 1, swipe the first white card. When it appears 2, swipe the second card. When it appears 3, if you don’t have the third white card, swipe any white card. The meter will automatically shut down at this time. There will be a beep each time you swipe a card. Short press the power button and swipe the white card to turn on the meter.

Startup Using NFC Sub-Card:

  • Briefly press the power button and swipe a white sub-card over the NFC area.

Key Functions:

  1. Key 1 (Power):

    • Short Press: Power on.

    • Long Press: Power off.

  2. Keys 3 + 5: Press simultaneously to enter backend settings.

Backend Parameters (Partial List):

    • P01: Backlight brightness adjustment (1-10 levels).

    • P02: Odometer unit selection (0: km, 1: mile, 2: km and mile dual display).

    • P03: Voltage level setting (24V, 36V, 48V, 52V, 60V, 72V).

    • P04: Sleep timer setting (0: disabled; 1-60 minutes).

    • P06: Wheel diameter adjustment (unit: inch; precision: 0.1).

    • P07: Magnet count setting for speed measurement (1-100).

    • P09: Zero-start/non-zero-start selection (0: zero-start; 1: non-zero-start).

    • P10: Drive mode setting (0: pedal assist; 1: electric drive; 2: dual mode).

    • P11: Pedal assist sensitivity (1-24 levels).

    • P12: Starting torque adjustment (0-5 levels, 0: weakest, 5: strongest).

    • P13: Pedal magnet type setting (5, 8, 12 poles).

    • P15: Motor drive signal percentage (100% = full speed).

    • P16: Real-time cruise control (0: disabled; 1: enabled).

    • P19: Taillight setting (0: always on; 1: synchronized with headlights).

    • P20: Startup mode selection (0: ECO PRO soft start; 1: COMFORT normal start; 2: SPORT hard start).

    • P21: Electronic brake strength (0: disabled; 1-10: adjustable levels).

    • P22: Throttle Hall sensor setting (0: disabled; 1: enabled).

    • P23: Password modification (short press Key 3 to edit).

    • P95: Startup security mode (0: no password/NFC; 1: NFC only; 2: password + NFC).

    • P96: Speed limit settings (0: locked at 40 km/h; 1: temporary unlock via long press Key 3; 2: permanent unlock requiring restart).

    • P97: Drive icon display (0: hidden; 1: single/dual drive toggle; 2: default dual drive).

    • P98: One-touch startup (0: disabled; 1: enabled).

    • P99: Factory reset (long press Key 3 for 5-6 seconds in P99 interface).

    • ODO: odo reset (in the ODO parameter interface, short press button 3, then long press button 3 for 5-6 seconds until the number is reset and then release it)

Operation Instructions

Long press the No. 2 button to turn on the headlights/long press to turn off the headlights. At the same time, the headlight icon will light up or turn off synchronously with the button. Short press the No. 2 button to switch the start mode.

Long press the No. 3 button to enter the speed limit and light up the speed limit icon. Short press the No. 3 button to flip ODO/TRIP/TIME/fault code E/voltage V.

Long press the No. 5 button to light up the 6 km human icon and turn on this function. Long press the No. 5 button again to cancel the human icon and return to the current gear.

The No. 4 button is for single and dual drive switching. This button works in a cycle. Short press the No. 4 button to switch various drive modes. For example, if the front drive is working, the icon F is lit, if the rear drive is working, the icon B is lit, and if the dual drive is working, the icons F and B are lit at the same time.

Short press button 5 for gear position, this button also works in a cycle, currently the highest gear is 3, press button 3 and button 5 at the same time to enter the background (after entering the background, to modify the parameters, you need to short press button 3. When the number is flashing, you can modify the parameters through button 4 and button 5. At this time, short press button 4 to subtract -, short press button 5 to add +, after adjusting the parameters you want, you need to long press button 3 until the number does not flash, indicating that the setting is successful). After entering the background, when you do not modify the parameters, buttons 4 and 5 can switch P01-ODO and can be used as up and down buttons. After the parameter adjustment is completed, press buttons 3 and 5 at the same time to return to the home page.

 

Password setting
First, the factory comes with a default password (1234). Let's explain how to set the password. Enter the background and select P95. Here is an example to select 2. When we select 2 on P95, the P93 function is turned on and an initial password 1234 will be generated. Let's talk about changing the password. When the password is set successfully and you want to change the password, adjust the parameter to P93 and you can see the factory password 1234. Short press button 3. At this time, the ENTER PASSWORD icon on the main interface starts to light up and stays on. The number below the icon starts to flash and 4 horizontal bars appear. At this time, enter the 4-digit password you want to confirm. Short press button 3. The number does not flash. The icon ENTER PASSWORD means that the password is set successfully. If you need to change it again, you can do it by analogy. When P95 selects password/NFC, short press button 1 every time the instrument is restarted, and only this icon will appear on the main interface when it is turned on! !
And when the number turns into 4 horizontal bars, the user needs to enter the correct password to restore the main interface (long press when entering the first number, but not the subsequent numbers) or directly use the NFC card to flash the machine. Both coexist, and whichever is used first takes priority.

 

Here is an explanation of the startup mode.

This is the icon that lights up for each different startup mode. The factory default is ECO PRO, which is a soft-start energy-saving mode. You can set the default startup mode in the background. Enter the background and select P20 to adjust 0 for ECO PRO, 1 for COMFORT, and 2 for SPORT. During driving, you can switch between various startup modes by short pressing button 2. Button 2 works in a cycle. P20 in the background is the default startup option.

 The specified time for short-pressing the button is 0.3 seconds, and the specified time for long-pressing the button is 2 seconds.


Note: Due to the upgrade of the company's products, some of the displayed content of the product you get may be different from the manual, but it will not affect your normal use.